Online only

Fall protection parapet with worktop MH60

Valutazione 

MH60

New product

PISCOPIELLO PONTEGGI

Disponibile

Parapet post designed to allow the installation of a worktop with max. of 100 cm. TECHNICAL SHEET FOR MH60 UPRIGHT

ATTENTION THIS PRODUCT HAS BEEN REPLACED BY: MH55 PLUS

More details

Request product info

More info

This parapet post has the predisposition for a worktop with a maximum width of 100 cm. The vertical upright itself has a height of 115 cm.
The upright Mod. MH60 is fixed to the wall by means of an M24 threaded bar and a counter flange. The bodyguard is made with a 48 mm Ø tube and for this reason it is possible to install the scaffolding boards with a maximum width of 100 cm and in any case respecting the center distance shown in the use and maintenance booklet.

elementi montante parapetto mh18maxi

Montante parapetto - sistema di protezione collettiva Mh18

The railing MH 60 (fig_3) consists of the following elements:
Vertical uprights made with hollow tubes of round section 42 * 2 mm 111.5 cm long arranged with a maximum pitch of 120 cm (for needs of checks on the service limit states in terms of walkway) (1); N ° 3 brackets fixed to the uprights to house the handrail boards and the lower beams with section B * S = 30 * 2.5 mm cold-shaped tape to stiffen it, L-shaped with Dorizz * Dvert = 65 * dimensions 130 mm and welded on uprights with a pitch of about 50cm (2); Structural shelf made up of a hollow tubular horizontal element with a round section, external diameter 48mm, 2mm thick and 101cm long (3), which acts as a support for the panels that make up the walkway, which in turn is connected by welding to a tubular element. cable of vertical square section and dimensions 50 * 50 * 2mm of length 100cm (4), which at about 80cm from the connection node with your ø 48mm, is connected to an oblique tube cable of square section and dimensions 30 * 30 * 2mm length 127cm (5), in turn connected with the horizontal element with the vertical tube ø 48mm (3); Bar for anchoring to the existing wall of 24mm diameter (6); Closing flange with external diameter 130 mm with nut type M26 for fixing to the bar diam 24mm (7).


Reference standards and certifications
UNI EN 13374: 2004 standard
Temporary edge protection systems' product specification and test methods.
UNI EN 12811.1: 2004 standard
Temporary systems for access plans and work at height 'specify performance requirements and design methods (for parapets that also act as walking surfaces and work areas).
Legislative Decree No. 81 of April 90, 2008
Protection of health and safety in the workplace.
The parapet has not been tested by any laboratory since being usable for roofs belonging to class A, i.e. for slopes less than 10 ° (equal to a slope of 18%), a project drawn up by an engineer is sufficient enabled and there is no obligation to carry out laboratory tests in accordance with point 5.2.1 of UNI EN 13374 standards.

Parapet Technical Sheet

Useful Height

115 cm

Maximum distance from the facade of the building 

14.0 cm

Riser tube

42x2.0 mm

Support tubeTubo support

-

Parapet weight

7.0 kg

Certification

class A according to EN 13374: 2013

Center distance of the uprights

120 cm

Threaded rodM24
Section anchor plate-
Section support plate

-

Reviews

Grade 
11/14/2020

PARAPETTO ANTICADUTA

BUON PRODOTTO

    Write a review

    Fall protection parapet with worktop MH60

    Fall protection parapet with worktop MH60

    Parapet post designed to allow the installation of a worktop with max. of 100 cm. TECHNICAL SHEET FOR MH60 UPRIGHT

    ATTENTION THIS PRODUCT HAS BEEN REPLACED BY: MH55 PLUS

    17 other products in the same category:

    Viewed products

    Top sellers

    Specials

    Follow us on Facebook